ISO 10328-2006 修复术.假腿的结构试验.要求和试验方法.pdf

标准号：ISO 10328-2006
实施状态：作废
中文名称：修复术.假腿的结构试验.要求和试验方法
英文名称：Prosthetics - Structural testing of lower-limb prostheses - Requirements and test methods
发布日期：2006-10
被替代标准：ISO 10328-2016
代替标准：ISO/FDIS 10328-2006;ISO 10328-1-1996;ISO 10328-2-1996;ISO 10328-3-1996;ISO 10328-4-1996;ISO 10328-5-1996;ISO 10328-6-1996;ISO 10328-7-1996;ISO 10328-8-1996
采用标准：DIN EN ISO 10328-2007,IDT;BS EN ISO 10328-2006,IDT;EN ISO 10328-2006,IDT;NF S96-802-2006,IDT;SN EN ISO 10328-2007,IDT;OENORM EN ISO 10328-2007,IDTN-EN ISO 10328-2007,IDT;UNE-EN ISO 10328-2007,IDT;GOST R ISO 10328-2007,IDT
起草单位：ISO/TC 168
标准简介：IMPORTANT — This International Standard is suitable for the assessment of the conformity of lower
limb prosthetic devices/structures with the strength requirements specified in 4.4 of ISO 22523:2006
(see NOTE 1). Prosthetic ankle-foot devices and foot units on the market, which have demonstrated
their compliance with the strength requirements specified in 4.4 of EN 12523:1999 through submission
to the relevant tests of ISO 10328:1996, need not be retested to ISO 22675:2006.
This International Standard specifies procedures for static and cyclic strength tests on lower-limb prostheses
(see NOTE 2) which typically produce compound loadings by the application of a single test force. The
compound loads in the test sample relate to the peak values of the components of loading which normally
occur at different instants during the stance phase of walking.
The tests described in this International Standard comprise
⎯ principal static and cyclic tests for all components;
⎯ a separate static test in torsion for all components;
⎯ separate static and cyclic tests on ankle-foot devices and foot units for all ankle-foot devices as single
components including ankle units or ankle attachments and all foot units as single components;
⎯ a separate static ultimate strength test in maximum knee flexion on knee joints and associated parts for
all knee units or knee-shin-assemblies and adjacent components that normally provide the flexion stop on
a complete prosthesis;
⎯ separate static and cyclic tests on knee locks for all mechanisms which lock the knee joint in the
extended position of the knee unit or knee-shin-assembly.
The tests described in this International Standard apply to specific types of ankle-disarticulation prostheses
(see NOTE 3), to transtibial (below-knee), knee-disarticulation and transfemoral (above-knee) prostheses and
to the distal (lower) part of hip-disarticulation and hemi-pelvectomy prostheses (see NOTE 4).
NOTE 1 ISO 22523 (formerly EN 12523) addresses those of the Essential Requirements listed in Annex 1 of the
European Medical Device Directive 93/42/EEC that are applicable to external limb prostheses and external orthoses.
NOTE 2 The tests can be performed on complete structures, on part structures or on individual components.
NOTE 3 The tests only apply to ankle-disarticulation prostheses which include (foot) components of prosthetic anklefoot
devices taken from the normal production line.
NOTE 4 The distal part comprises the knee unit, the ankle-foot device and all parts between. Tests on hip units are
described in ISO 15032.
文件格式：PDF
文件大小：6.13MB
文件页数：148
（以上信息更新时间为：2019-11-22）



文档语言及版本参照下方封面截图：