ISO 19901-7-2005 石油和天然气工业.海上建筑物的特殊要求.第7部分_浮动式海上建筑物和移动式海上设备用保持系统.pdf

标准号：ISO 19901-7-2005
实施状态：作废
中文名称：石油和天然气工业.海上建筑物的特殊要求.第7部分:浮动式海上建筑物和移动式海上设备用保持系统
英文名称：Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units
发布日期：2005-12
被替代标准：ISO 19901-7-2013
代替标准：ISO/TR 13637-1997;ISO/FDIS 19901-7-2005
采用标准：DIN EN ISO 19901-7-2006,IDT;BS EN ISO 19901-7-2006,IDT;EN ISO 19901-7-2005,IDT;NF M87-264-7-2006,IDT;CAN/CSA-ISO 19901-7-07-2007,IDT;SN EN ISO 19901-7-2006,IDT;OENORM EN ISO 19901-7-2006,IDTN-EN ISO 19901-7-2006,IDT
起草单位：ISO/TC 67
标准简介：This part of ISO 19901 specifies methodologies for
a) the design, analysis and evaluation of stationkeeping systems for floating structures used by the oil and gas industries to support
- production,
- storage,
- drilling, well intervention and production,
- production and storage,
- drilling, well intervention, production and storage, and
b) the assessment of stationkeeping systems for site-specific applications of mobile offshore units (e.g. mobile offshore drilling units, construction units, and pipelay units).
Most stationkeeping systems used with the class of floating structures covered by a) are termed “permanent mooring systems”, for which this part of ISO 19901 is applicable to all aspects of the life cycle and includes requirements relating to the manufacture of mooring components, as well as considerations for in-service inspections. Most stationkeeping systems used with mobile offshore units, the class covered by b), are termed“mobile mooring systems”. Throughout this document, the term “floating structure”, sometimes shortened to“structure”, is used as a generic term to indicate any member of the two classes, a) and b).
This part of ISO 19901 is applicable to the following types of stationkeeping systems, which are either covered directly in this document or through reference to other guidelines:
- spread moorings (catenary, taut-line and semi-taut-line moorings);
- single point moorings, anchored by spread mooring arrangements;
- dynamic positioning systems;
- thruster-assisted moorings.
Descriptions of the characteristics and of typical components of these systems are given in Annex A.
The requirements of this part of ISO 19901 mainly address spread mooring systems and single point mooring systems with mooring lines composed of steel chain and wire rope. This document also provides guidance on the application of the methodology to synthetic fibre rope mooring systems, and includes additional requirements related to the unique properties of synthetic fibre ropes.
The document applies to single anchor leg moorings (SALMs) and other single point mooring systems (e.g. tower soft yoke systems) only to the extent to which the requirements are relevant.
The requirements of this document do not apply to the vertical moorings of tension leg platforms (TLPs).
The methodology described in this part of ISO 19901 identifies a set of coherent analysis tools that, combined with an understanding of the site-specific metocean conditions, the characteristics of the floating structure under consideration, and other factors, can be used to determine the adequacy of the stationkeeping system to meet the document’s functional requirements.
文件格式：PDF
文件大小：1.49MB
文件页数：126
（以上信息更新时间为：2019-11-22）



文档语言及版本参照下方封面截图：