标准号：ISO 18414-2006
实施状态：作废
中文名称：按属性验收取样规程.基于控制出厂质量信用原则的验收零取样系统
英文名称：Acceptance sampling procedures by attributes - Accept-zero sampling system based on credit principle for controlling outgoing quality
发布日期：2006-01
被替代标准：ISO 28593-2017
代替标准：ISO/FDIS 18414-2005
采用标准：DIN ISO 18414-2012,IDT;DIN ISO 18414-2010,IDT;BS 6001-7-2006,IDT;GB/T 26823-2011,IDT;KS A ISO 18414-2008,IDT;KS A ISO 18414-2015,IDT;GOST R ISO 18414-2008,IDT;DS/ISO 18414-2006,IDT;DS/ISO 18414-2006,IDT;NEN-ISO 18414-2006 en-2006,IDT
起草单位：ISO/TC 69
标准简介：1.1 This International Standard specifies a system of single sampling schemes for lot-by-lot inspection by
attributes. All the sampling plans of the present system are of accept-zero form, i.e. no lot is accepted if the
sample from it contains one or more nonconforming items. The schemes depend on a suitably-defined
average outgoing quality limit (AOQL), the value of which is chosen by the user; no restrictions are placed on
the choice of the value of the AOQL or on the sizes of successive lots in the series. The methodology ensures
that the overall average quality reaching the customer or market-place will not exceed the AOQL in the long
run.
1.2 The schemes are intended to induce a supplier, through the economic and psychological pressure of lot
non-acceptance and consequent loss of accumulated credit, to attempt to maintain a nonconformity-free
process, while assuring, by means of the lowest practicable sample sizes, that the long-term percentage of
nonconforming items delivered to the customer or market-place does not exceed the AOQL. This objective is
achieved by a progressive reduction in the sample size in response to good quality history.
1.3 The schemes are designed to be applied to a series of lots from each supplier. The credit principle
provides:
a) automatic protection to the customer if a deterioration in quality is detected, by means of a total loss of
accumulated credit and reversion to a relatively large sample size whenever a nonconforming item is
found, and 100 % inspection of
1) the first lot if it is not accepted, or
2) any non-accepted lot that immediately follows a non-accepted lot;
b) an incentive to reduce sampling costs (by means of a progressive reduction in required sample size) if
consistently good quality is achieved.
1.4 This International Standard is designed for use under the following conditions:
a) where the inspection procedure is to be applied to a series of lots of discrete items that are intended to be
identical, and which are all supplied by one producer using one production process (If there are different
producers or production processes, this International Standard is intended to be applied to each one
separately.);
b) where one or more quality characteristics of these products are taken into consideration, which must all
be classifiable as either conforming or nonconforming;
c) where the inspection error involved in classifying the state of a product's quality characteristic(s) is
negligible;
d) where inspection is non-destructive.
This International Standard can be suitable for regulatory purposes, as control of the expected quality of items
reaching the market-place is achieved with the smallest possible sample sizes, and long-term control of the
realized, or actual quality level in the market-place is achieved with certainty, regardless of how long or short
individual suppliers' series may be. This International Standard can be used by suppliers/producers,
buyers/consumers and regulatory agencies to provide control of the expected quality of the totality of accepted
product of each type from each source.
文件格式：PDF
文件大小：375.54KB
文件页数：14
（以上信息更新时间为：2019-11-22）
ISO 18414-2006 按属性验收取样规程.基于控制出厂质量信用原则的验收零取样系统.pdf
(375.54 KB)
|
|
