标准号：ISO 11960-2004
实施状态：作废
中文名称：石油和天然气工业.油井套管和油管用钢管
英文名称：Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells
发布日期：2004-12
被替代标准：ISO 11960-2011
代替标准：ISO 11960-2001;ISO/FDIS 11960-2004;ISO 11960 Technical Corrigendum 1-2002
采用标准：DIN EN ISO 11960-2005,IDT;API SPEC 5CT-2005,NEQ;API SPEC 5CT ERTA 1-2006,MOD;API SPEC 5CT ERTA 2-2006,MOD;ANSI/API SPEC 5CT-2007,IDT;BS EN ISO 11960-2005,IDT;EN ISO 11960-2004,IDT;NF M87-207-2005,IDT;SN EN ISO 11960-2005,IDT;SN EN ISO 11960/AC-2007,IDT;OENORM EN ISO 11960-2005,IDT;PN-EN ISO 11960-2005,IDT;PN-EN ISO 11960-2010,IDT;GOST R 53366-2009,IDT
起草单位：ISO/TC 67
标准简介：1.1 This International Standard specifies the technical delivery conditions for steel pipes (casing, tubing,
plain-end casing liners and pup joints), coupling stock and accessories and establishes requirements for three
Product Specification Levels (PSL-1, PSL-2, PSL-3). The requirements for PSL-1 are the basis of this
International Standard. The requirements that define different levels of standard technical requirements for
PSL-2 and PSL-3, for all Grades except H-40 and L-80 9Cr, are contained in Annex H.
For pipes covered by this International Standard, the sizes, masses and wall thicknesses as well as grades
and applicable end-finishes are listed in Tables C.1 to C.3 and Tables E.1 to E.3.
By agreement between the purchaser and manufacturer, this International Standard can also be applied to
other plain-end pipe sizes and wall thicknesses.
This International Standard is applicable to the following connections in accordance with API Spec 5B:
short round thread casing (STC);
long round thread casing (LC);
buttress thread casing (BC);
extreme-line casing (XC);
non-upset tubing (NU);
external upset tubing (EU);
integral joint tubing (IJ).
For such connections, this International Standard specifies the technical delivery conditions for couplings and
thread protection. Supplementary requirements that may optionally be agreed for enhanced leak resistance
connections are given in Annex A.11 (SR22).
This International Standard can also be applied to tubulars with connections not covered by ISO/API
standards.
1.2 The four groups of products to which this International Standard is applicable include the following
grades of pipe:
Group 1: All casing and tubing in Grades H, J, K and N;
Group 2: All casing and tubing in Grades C, L, M and T;
Group 3: All casing and tubing in Grade P;
Group 4: All casing in Grade Q.
1.3 Casing sizes larger than Label 1: 4-1/2 but smaller than Label 1: 10-3/4 may be specified by the
purchaser to be used in tubing service, see Tables C.1, C.24, C.30 and C.31 or Tables E.1, E.24, E.30 and
E.31.
1.4 Supplementary requirements that may optionally be agreed between purchaser and manufacturer for
non-destructive examination, coupling blanks, upset casing, electric-welded casing, impact testing, seal ring
couplings and certificates are given in Annex A.
1.5 This International Standard is not applicable to threading requirements.
文件格式：PDF
文件大小：3.16MB
文件页数：300
（以上信息更新时间为：2019-11-22）
ISO 11960-2004 石油和天然气工业.油井套管和油管用钢管.pdf
(3.16 MB)
|
|
